Hunter X Core Manual Start

Reset a Hunter XCore irrigation controller YouTube

In this video tutorial I show you how to factory reset the Hunter X-CORE Residential Irrigation Controller step by step. This will erase all settings includi.

Hunter Xcore Sprinkler Manual

1 X-Core Components. 2 Setup. 2.1 SETTING THE CURRENT DATE AND TIME. 2.2 SETTING A PROGRAM START TIME. 2.3 ELIMINATING A PROGRAM START TIME. 2.4 SETTING A STATION RUN TIME. 2.5 SETTING WATER DAYS. 2.6 SELECTING ODD OR EVEN DAYS TO WATER. 2.7 SELECTING INTERVAL WATERING.

how to program hunter X core controller YouTube

Attach the two yellow wires to the AC terminals. receiver to the wall next to the irrigation 2. Page 322 The reCeiver Wiring the receiver to a hunter X-Core, pro-C, Wiring the receiver to a hunter aCC iCC and i-Core 1. Connect the blue and white wire to any of the four Sensor Terminal pairs (Sen 1 shown). 1.

Como programar controlador xcore hunter YouTube

If you have an X Core controller that seems to be playing up then the most likely cause is that it needs resetting. This can be done easily. 1. Press and hold the 'PROG' button. 2. While holding the 'PROG' button press the RESET button for 3 seconds, then release the RESET button while continuing to hold the 'PROG' button. 3.

Hunter X Core Manual Start

Resetting X-Core. Press and hold down the , and buttons simultaneously. Press and release the RESET button on the right side of the controller. When DONE appears on the LCD, release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed. Reset procedure for the Hunter X.

Controlador Hunter XCore 2 estações Interno Casairriga

In this video, Clint shows us how to hard reset a Hunter X-Core Irrigation controller. Resetting a Hunter X-Core is easy. To reset the irrigation controller,.

Hunter XCore Programming Overview and Setting Up Program A YouTube

Page 28: Program Customization. The X-Core is factory configured with three independent programs (A, B, C) with four start times each for different plant type requirements. The X-Core can be customized to display only one program and one start time, hiding extra unneeded programs and start times to ease programming.

hunter x core quick check and reset features Manualzz

Press and release the RESET button in the lower wiring compartment. Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed. X-Core. Press and hold down the , and buttons. Press and release the RESET button on the right side of the controller.

Hunter XCore computer PVC24.nl

Maximum Solenoids per Output. Welcome to the X-Core irrigation controller support section. The X-Core, which is the XC timer predecessor, is Hunter's professional controller for 2 to 8 zones. This section will show you how to install, program and troubleshoot your X-Core controller.

Hunter XCore Residential Indoor Controller Sierra Irrigation

To reset a Hunter x Core irrigation controller to its factory default settings, follow these steps: Turn off the power to the controller by unplugging it or switching off the circuit breaker. Locate the small reset button on the back of the controller. Using a paperclip or similar object, press and hold the reset button for at least 5 seconds.

Hunter XCore Irrigation Controller

X-Core. Press and hold down the , and buttons. Press and release the RESET button on the right side of the controller. Wait 2 seconds and release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

HUNTER XCORE Programming Program and Setup (Easy) YouTube

Use the PRG button to select program (A, B, or C). 3. Use the + and - buttons to change the Start Time. The Start Time advances in 15-minute increments. 4. Press the button to add another Start Time, or PRG button to set a Start Time for the next program. 5. Turn the dial to the RUN position. ELIMINATING A PROGRAM START TIME 1.

Hunter XCORE timer irrigation video 3of4 Irrigation Systems Install/Repair in New York and

X-Core - Reset / Clearing the Controllers Memory. Reset a Hunter Controller - Quick Tip. Watch on. Press and hold the button. While holding the button, press the RESET button for 3 seconds then release while continuing to hold the button. Continue holding the button until the display shows 12:00am or "DONE".

How to program a Hunter Xcore controller YouTube

Solution. RED (AC1), WHITE (AC2) and BLUE (REM terminal) Check the master valve or pump start wire for continuity. Replace or repair the shorted wire. Check that all wire connections are good and watertight. Check electrical specifications for pump relay - Do not exceed controller's electrical rating. Replace defective pump relay or solenoid.

Hunter X Core Sprinkler Controller

HUNTER X CORE TROUBLESHOOTING GUIDE PROBLEMS . The Controller is continually watering . CAUSES . Too many start times have been programmed .. Press and release the RESET button on the back of the front panel. Wait until the display shows 12:00am. Release the may now be reprogrammed. button. All the memory has been cleared and the controller.

Hunter Xcore 사용 설명서

In this 'How To' video, our Smart Water Shop Operations Manager - Matthew Bristowe - shows us how to factory reset a Hunter X-Core Irrigation Controller. Th.